I got my router in today, opened it up and took high-res photos of the system board. Both the firmware and the chips confirm it is an Atheros AP81 router platform.
OpenWRT current status
Trunk now has support to flash this router. See the threads on the Trendnet TEW-652BRP (similar Atheros AP81, but flash is not identical).
1. USB port is working perfect, reports later in the thread.
2. [s]LAN interface is not yet working (eth0). Linux does not have drivers for the Atheros AR8216 / AR8316 Ethernet switch parts. [/s] A new change checked in SVN 14655 to get the LAN ports working. So now LAN and WAN ports should be working fine (please provide test feedback).
3. see the Trendnet TEW-652BRP thread for issues with limitations and performance of the ath9k wireless driver. http://forum.openwrt.org/viewtopic.php?id=18314
I have asked Planex to provide a GPL release for this router including u-boot. No response so far.
For reference, if you need to flash from u-boot, here is instructions:
ar7100> erase 0xbf050000 +0x770000
ar7100> setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1
ar7100> tftp 0xa0800000 openwrt-ar71xx-mzk-w04nu-squashfs.bin
ar7100> cp.b 0xa0800000 0xbf050000 0x770000
ar7100> reset
You do NOT need to flash from u-boot, you can flash from the web interface. but one time by accident I managed to flash a build with no working LAN or wifi drivers, so I'm putting instructions here in case anyone else does this
Hardware Information
This should have the 3x3 MIMO AR9103 radio chip on it. This is the only consumer retail Atheros AP81 I know of shipping with USB port standard. This unit also has 8MB of FLASH, most only have 4MB.
High res photos:
http://sites.google.com/site/stephengut … 1_crop.jpg
http://sites.google.com/site/stephengut … _work1.JPG
Note that in these photos I has already moved around the internal antenna cables in the router. Originally they were all 3 run under the metal tab on the outside edge of the router. I moved the antenna cables for clearer photos and to untangle them a bit.
The antennas are all 3 removable, use the same Reverse SMA jack as the Trendnet TEW-632BRP, TEW-652BRP and TP-Link TL-WR941ND. The antennas themselves are about 40% to 50% longer on the Trendnet and T-Link than the Trendnet ones.
The Trendnet and Plenex use nearly identical power supplies in the USA, same Jentec brand but Trendnet is 5v 2.5amp, Planex is 5v 3amp. FCC ID of the Planex: sj9-mzkw04nu
There does not seem to be any form of http or tftp recovery if you botch the firmware. If you plan on building your own (untested) firmware, I suggest to get a Nokia DKU-5 cable or other rs232 solution on hand in case you have to flash from u-boot with serial port. The binaries I distribute: I try to test before I post them, so the are possibly safer.
serial port pinout: pin 1 (square box) = +3.3V, pin 2 = RX, pin 3 = TX, pin 4 = Ground. You only need to connect pin 2,3,4 (for a total of three wires).
Sourcing
These routers are selling for $59.99 including free shipping on Amazon.com in both the USA and Japan. Looks like Planex (PCI) is selling them directly. [s]UPDATE: As of Feburary 2, 2009 - Amazon.com no longer has any in stock, hopefully Planex will return to selling them in the USA.[/s] UPDATE: Feburary 11, 2009 - back on sale on Amazon.com in USA again.
Vendor firmware boot
Since we are still trying to tune the wireless drivers on these devices, I'm preserving full boot logs incase these noisy messages later reveal some secret chipset tuning or features. Planex vendor firmware version 1.00.03 Build Date Wed Nov 28 21:03:53 JST 2007:
U-Boot 1.1.4 (Oct 25 2007 - 15:28:59)
AP81 (ar7100) U-boot
DRAM:
sri
32 MB
Top of RAM usable for U-Boot at: 82000000
Reserving 222k for U-Boot at: 81fc8000
Reserving 192k for malloc() at: 81f98000
Reserving 44 Bytes for Board Info at: 81f97fd4
Reserving 36 Bytes for Global Data at: 81f97fb0
Reserving 128k for boot params() at: 81f77fb0
Stack Pointer at: 81f77f98
Now running in RAM - U-Boot at: 81fc8000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
Fetching MAC Address from 0x81fedb10
eth0: 00:90:cc:f4:9c:a6
dup 1 speed 100
eth0 up
eth0
====check reset button function====
### main_loop entered: bootdelay=4
### main_loop: bootcmd="bootm 0xbf050000"
Hit any key to stop autoboot: 0
## Booting image at bf050000 ...
Image Name: Linux Kernel Image
Created: 2007-11-28 12:04:01 UTC
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 1361970 Bytes = 1.3 MB
Load Address: 80060000
Entry Point: 80301000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80301000) ...
## Giving linux memsize in bytes, 33554432
Starting kernel ...
Linux version 2.6.15--LSDK-7.1.2.32 (ttajima@localhost.localdomain) (gcc version 3.4.4) #238 Wed Nov 28 21:03:53 JST
2007
flash_size passed from bootloader = 8
arg 1: console=ttyS0,115200
arg 2: root=31:03
arg 3: rootfstype=jffs2
arg 4: init=/sbin/init
arg 5: mtdparts=ar7100-nor0:256k(u-boot),64k(u-boot-env),1408k(uImage),6208k(rootfs),128k(config),128k(ART)
arg 6: mem=32M
CPU revision is: 00019374
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7100-nor0:256k(u-boo
t),64k(u-boot-env),1408k(uImage),6208k(rootfs),128k(config),128k(ART) mem=32M
Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 256 (order: 8, 4096 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29152k/32768k available (1985k kernel code, 3600k reserved, 702k data, 112k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
AR7100 GPIOC major 0
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
Serial: 8250/16550 driver $Revision: #2 $ 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
Creating 6 MTD partitions on "ar7100-nor0":
0x00000000-0x00040000 : "u-boot"
0x00040000-0x00050000 : "u-boot-env"
0x00050000-0x001b0000 : "uImage"
0x001b0000-0x007c0000 : "rootfs"
0x007c0000-0x007e0000 : "config"
0x007e0000-0x00800000 : "ART"
Port Status c000004
ar7100-ehci ar7100-ehci.0: ATH EHCI
ar7100-ehci ar7100-ehci.0: new USB bus registered, assigned bus number 1
ar7100-ehci ar7100-ehci.0: irq 3, io mem 0x1b000000
hcc_params addr 0xbb000108 val 0x6 hcs_params addr 0xbb000104 val 0x10011
ar7100-ehci ar7100-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Netfilter messages via NETLINK v0.30.
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
ip_conntrack version 2.4 (256 buckets, 2048 max) - 232 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ar7100wdt_init: Registering WDT success
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing unused kernel memory: 112k freed
mount: Mounting devpts on /dev/pts failed: No such file or directory
ag7100_mod: module license 'unspecified' taints kernel.
AG7100: Length per segment 1536
AG7100: Max segments per packet 1
AG7100: Max tx descriptor count 40
AG7100: Max rx descriptor count 252
AG7100: fifo cfg 3 00780008
AG7100CHH: Mac address for unit 0
AG7100CHH: 00:90:cc:f4:9c:a6
AG7100CHH: Mac address for unit 1
AG7100CHH: 00:90:cc:f4:9c:a7
AG7100: cfg1 0xf cfg2 0x7014
AG7100: unit 0 phy is up...RMii 100Mbps full duplex
AG7100: pll reg 0x18050014: 0x13000a44 AG7100: cfg_1: 0x7ff0000
AG7100: cfg_2: 0xfff
AG7100: cfg_3: 0x780008
AG7100: cfg_4: 0xffff
AG7100: cfg_5: 0x7ffef
AG7100: done cfg2 0x7115 ifctl 0x10000 miictrl 0x13
Writing 4
AG7100: cfg1 0xf cfg2 0x7014
ATHRS26: resetting s26
ATHRS26: s26 reset done
AG7100: unit 1: phy not up carrier 1
Writing 6
EOPNOTSUPP
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
(none) mips #238 Wed Nov 28 21:03:53 JST 2007
(none) login: EOPNOTSUPP
EOPNOTSUPP
ath_hal: 0.9.17.1 (AR5416, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
wlan: 0.8.4.2 (Atheros/multi-bss)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: no version for "_ath_hal_attach" found: kernel tainted.
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 0.9.4.5 (Atheros/multi-bss)
=====simple_config_callback registered=====
wifi0: Atheros AR9100 WiSoC: mem=0xb80c0000, irq=2
wlan: mac acl policy registered
ath_set_config: Setting ATH parameter
ath_set_config: Setting ATH parameter
ath_set_config: Setting ATH parameter
ath_set_config: Setting ATH parameter
ath_set_config: Setting ATH parameter
ieee80211_ioctl_setparam: CHH Calling ieee80211_open
EOPNOTSUPP
EOPNOTSUPP
RF 0x98b0 V 0x1e5795e5
RF 0x98e0 V 0x2008020
RF 0x98b0 V 0x2108421
RF 0x98ec V 0x8
RF 0x98b0 V 0xe73ff17
RF 0x98e0 V 0x420
RF 0x98f0 V 0x1c00018
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0xe00000
RF 0x989c V 0x5e0000
RF 0x989c V 0x120000
RF 0x989c V 0x620000
RF 0x989c V 0x20000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0x40ff0000
RF 0x989c V 0x5f0000
RF 0x989c V 0x870000
RF 0x989c V 0xf90000
RF 0x989c V 0x7b0000
RF 0x989c V 0xff0000
RF 0x989c V 0xf50000
RF 0x989c V 0xdc0000
RF 0x989c V 0x110000
RF 0x989c V 0x6100a8
RF 0x989c V 0x423022
RF 0x989c V 0x2014008f
RF 0x989c V 0xc40002
RF 0x989c V 0x3000f2
RF 0x989c V 0x440016
RF 0x989c V 0x410040
RF 0x989c V 0x1805e
RF 0x989c V 0xc0ab
RF 0x989c V 0xe1
RF 0x989c V 0x80
RF 0x989c V 0xd4
RF 0x98d0 V 0x10000f
RF 0x989c V 0x500
RF 0x989c V 0x800
RF 0x98cc V 0xe
Force rf_pwd_icsyndiv to 1 on 2412 (1 0)
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0xe00000
RF 0x989c V 0x5e0000
RF 0x989c V 0x120000
RF 0x989c V 0x620000
RF 0x989c V 0x20000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0x40ff0000
RF 0x989c V 0x5f0000
RF 0x989c V 0x870000
RF 0x989c V 0xf90000
RF 0x989c V 0x7b0000
RF 0x989c V 0xff0000
RF 0x989c V 0xf50000
RF 0x989c V 0xdc0000
RF 0x989c V 0x110000
RF 0x989c V 0x6100a8
RF 0x989c V 0x423022
RF 0x989c V 0x1014008f
RF 0x989c V 0xc40002
RF 0x989c V 0x3000f2
RF 0x989c V 0x440016
RF 0x989c V 0x410040
RF 0x989c V 0x1805e
RF 0x989c V 0xc0ab
RF 0x989c V 0xe1
RF 0x989c V 0x80
RF 0x989c V 0xd4
RF 0x98d0 V 0x10000f
--AP ar5416InitUserSettings ahp->ah_miscMode 0x8
ar5416Reset Setting CFG 0x10a
Country ie is <6>RF 0x98b0 V 0x1e5795e5
RF 0x98e0 V 0x2008020
RF 0x98b0 V 0x2108421
RF 0x98ec V 0x8
RF 0x98b0 V 0xe73ff17
RF 0x98e0 V 0x420
RF 0x98f0 V 0x1c00018
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0xe00000
RF 0x989c V 0x5e0000
RF 0x989c V 0x120000
RF 0x989c V 0x620000
RF 0x989c V 0x20000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0x40ff0000
RF 0x989c V 0x5f0000
RF 0x989c V 0x870000
RF 0x989c V 0xf90000
RF 0x989c V 0x7b0000
RF 0x989c V 0xff0000
RF 0x989c V 0xf50000
RF 0x989c V 0xdc0000
RF 0x989c V 0x110000
RF 0x989c V 0x6100a8
RF 0x989c V 0x423022
RF 0x989c V 0x2014008f
RF 0x989c V 0xc40002
RF 0x989c V 0x3000f2
RF 0x989c V 0x440016
RF 0x989c V 0x410040
RF 0x989c V 0x1805e
RF 0x989c V 0xc0ab
RF 0x989c V 0xe1
RF 0x989c V 0x80
RF 0x989c V 0xd4
RF 0x98d0 V 0x10000f
RF 0x989c V 0x500
RF 0x989c V 0x800
RF 0x98cc V 0xe
Force rf_pwd_icsyndiv to 2 on 2422 (1 0)
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0xe00000
RF 0x989c V 0x5e0000
RF 0x989c V 0x120000
RF 0x989c V 0x620000
RF 0x989c V 0x20000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0x40ff0000
RF 0x989c V 0x5f0000
RF 0x989c V 0x870000
RF 0x989c V 0xf90000
RF 0x989c V 0x7b0000
RF 0x989c V 0xff0000
RF 0x989c V 0xf50000
RF 0x989c V 0xdc0000
RF 0x989c V 0x110000
RF 0x989c V 0x6100a8
RF 0x989c V 0x423022
RF 0x989c V 0x2014008f
RF 0x989c V 0xc40002
RF 0x989c V 0x3000f2
RF 0x989c V 0x440016
RF 0x989c V 0x410040
RF 0x989c V 0x1805e
RF 0x989c V 0xc0ab
RF 0x989c V 0xe1
RF 0x989c V 0x80
RF 0x989c V 0xd4
RF 0x98d0 V 0x10000f
--AP ar5416InitUserSettings ahp->ah_miscMode 0x8
ar5416Reset Setting CFG 0x10a
device ath0 entered promiscuous mode
br0: port 2(ath0) entering learning state
../../common/MasterControl/Info.cpp(66):Info::SetWscConfigPath: called
../../common/MasterControl/Info.cpp(79):Info::S
etAPNumRadio: called
******************************************************
Wi-Fi Simple Config Application - Atheros C
ommuncations
*********************************************************
../../common/UdpLib/UdpLib.cpp(78):Entered udp_o
pen
../../common/UdpLib/UdpLib.cpp(96):Socket open successful, sd: 3
../../common/UdpLib/UdpLib.cpp(114):Entered udp_bi
nd
../../common/UdpLib/UdpLib.cpp(129):Binding successful for socket [3]
../../common/WscCmd/WscCmd.cpp(405):WscCmd:Act
ualCBThreadProc: Started
../../common/WscCmd/WscCmd.cpp(1111):WscCmd:ActualUIThreadProc: Started.
killall: udhcpd: no p
rocess killed
killall: udhcpc: no process killed
../../common/MasterControl/MasterControl.cpp(88):MasterControl constru
ctor
../../common/WscCmd/WscCmd.cpp(243):WscCmd::MC instantiated ok
../../common/Transport/Transport.cpp(79):CTransport
Construction
../../common/MasterControl/MasterControl.cpp(209):MC::Init: Init complete ok
../../common/WscCmd/WscCmd.c
pp(245):WscCmd::MC intialized ok
../../common/WscCmd/WscCmd.cpp(119):WscCmd::Init ok, starting stack...
../../common/Ma
sterControl/Info.cpp(156):Read WSC Config File:/tmp/ath/wsc_config.txt
../../common/MasterControl/Info.cpp(171):Info::
ReadConfigFile:File open ok
../../common/MasterControl/Info.cpp(1273):Use eth0 address 0:90:cc:f4:9c:a6
../../common/T
ransport/Transport.cpp(154):In CTransport::ActualCBThreadProc
../../common/Transport/Transport.cpp(158):Calling Dequeu
e
../../common/MasterControl/MasterControl.cpp(1222):MC::SwitchModeOn: EModeApProxyRegistrar enter
../../common/StateMa
chine/StateMachine.cpp(71):RegistrarSM constructor
../../common/MasterControl/MasterControl.cpp(2961):***** WPA_PSK =
../../common/StateMachine/RegistrarSM.cpp(73):InitializeSM, locEna=1, Passthr=1
../../common/InbEap/InbEap.cpp(95):CIn
bEap Construction
../../common/InbEap/InbEap.cpp(114):Sizeof(WSC_NOTIFY_DATA) = 19
../../common/UdpLib/UdpLib.cpp(78):E
ntered udp_open
../../common/UdpLib/UdpLib.cpp(96):Socket open successful, sd: 7
../../common/UdpLib/UdpLib.cpp(114):En
tered udp_bind
../../common/UdpLib/UdpLib.cpp(129):Binding successful for socket [7]
../../common/InbWlan/InbWlan.cpp(7
3):CInbWlan Construction
../../common/UdpLib/UdpLib.cpp(78):Entered udp_open
../../common/UdpLib/UdpLib.cpp(96):Socket
open successful, sd: 8
../../common/UdpLib/UdpLib.cpp(114):Entered udp_bind
../../common/UdpLib/UdpLib.cpp(129):Binding
successful for socket [8]
../../common/InbEap/InbEap.cpp(360):In CInbEap::StaticRecvThread
../../common/InbEap/InbEap.
cpp(372):CInbEap::ActualRecvThread Started
../../common/StateMachine/StateMachine.cpp(71):RegistrarSM constructor
../..
/common/MasterControl/MasterControl.cpp(2757):Generated devPwd: 12345670
../../common/WscCmd/WscCmd.cpp(450):WscCmd:Ac
tualCBThreadProc: CB_MAIN_PUSH_MSG recd
../../common/WscCmd/WscCmd.cpp(1433):WscCmd::CallbackProc Enqueue done
../../co
mmon/MasterControl/MasterControl.cpp(1370):*** Init Enrolle Stat machine
../../common/MasterControl/MasterControl.cpp(
1379):MC::SwitchModeOn: Starting AP
../../common/WscCmd/WscCmd.cpp(502):WscCmd:ActualCBThreadProc: CB_MAIN_START_AP re
cd
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
../../common/WscCmd/WscCmd.cpp(1446):WscCmd::
AP tmp file =cp /tmp/ath/hostapd.open
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
../../comm
on/WscCmd/WscCmd.cpp(1433):WscCmd::CallbackProc Enqueue done
../../common/MasterControl/MasterControl.cpp(1419):MC::Sw
itchModeOn: Exit
../../common/MasterControl/MasterControl.cpp(352):MC::StartStack: Informing app of mode
../../common/W
scCmd/WscCmd.cpp(1433):WscCmd::CallbackProc Enqueue done
../../common/MasterControl/MasterControl.cpp(371):MC::SwitchM
odeOn: Done callback
../../common/WscCmd/WscCmd.cpp(123):WscCmd:: Stack started ok
../../common/InbWlan/InbWlan.cpp(288
):In CInbWlan::StaticRecvThread
../../common/InbWlan/InbWlan.cpp(313):CInbWlan::ActualRecvThread Started
../../common/I
nbWlan/InbWlan.cpp(317):Inside the thread
../../common/UdpLib/UdpLib.cpp(210):Entered udp_read
../../common/WscCmd/WscC
md.cpp(1452):WscCmd::AP Config file copied: cmd=cp /tmp/ath/hostapd.open /tmp/ath/hostapd.conf
../../common/MasterCont
rol/Info.cpp(73):Info::GetWscConfigPath: called
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
ssid=planexuser
../../common/WscCmd/WscCmd.cpp(1621):WscCmd::Params added to AP config file
../../common/MasterControl/
Info.cpp(73):Info::GetWscConfigPath: called
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
ssid
=planexuser
../../common/WscCmd/WscCmd.cpp(1621):WscCmd::Params added to AP config file
../../common/MasterControl/Info
.cpp(374):mb_nwKeySet = 1
../../common/MasterControl/Info.cpp(382):m_nwKey =
../../common/MasterControl/Info.cpp(73):I
nfo::GetWscConfigPath: called
route: SIOC[ADD|DEL]RT: No such process
Configuration file: /tmp/ath/hostapd.conf
ath_netd
ev_stop: The stopping of the running
br0: port 2(ath0) entering disabled state
Using interface ieee80211_ioctl_setparam: CHH Calling ieee80211_open
ath0 with hwaddr 00:90:cc:f4:9c:a6 and ssid 'planexuser'
RF 0x98b0 V 0x1e5795e5
RF 0x98e0 V 0x2008020
RF 0x98b0 V 0x2108421
RF 0x98ec V 0x8
RF 0x98b0 V 0xe73ff17
RF 0x98e0 V 0x420
RF 0x98f0 V 0x1c00018
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0xe00000
RF 0x989c V 0x5e0000
RF 0x989c V 0x120000
RF 0x989c V 0x620000
RF 0x989c V 0x20000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0x40ff0000
RF 0x989c V 0x5f0000
RF 0x989c V 0x870000
RF 0x989c V 0xf90000
RF 0x989c V 0x7b0000
RF 0x989c V 0xff0000
RF 0x989c V 0xf50000
RF 0x989c V 0xdc0000
RF 0x989c V 0x110000
RF 0x989c V 0x6100a8
RF 0x989c V 0x423022
RF 0x989c V 0x2014008f
RF 0x989c V 0xc40002
RF 0x989c V 0x3000f2
RF 0x989c V 0x440016
RF 0x989c V 0x410040
RF 0x989c V 0x1805e
RF 0x989c V 0xc0ab
RF 0x989c V 0xe1
RF 0x989c V 0x80
RF 0x989c V 0xd4
RF 0x98d0 V 0x10000f
RF 0x989c V 0x500
RF 0x989c V 0x800
RF 0x98cc V 0xe
Force rf_pwd_icsyndiv to 2 on 2422 (1 0)
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0x0
RF 0x989c V 0xe00000
RF 0x989c V 0x5e0000
RF 0x989c V 0x120000
RF 0x989c V 0x620000
RF 0x989c V 0x20000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0xff0000
RF 0x989c V 0x40ff0000
RF 0x989c V 0x5f0000
RF 0x989c V 0x870000
RF 0x989c V 0xf90000
RF 0x989c V 0x7b0000
RF 0x989c V 0xff0000
RF 0x989c V 0xf50000
RF 0x989c V 0xdc0000
RF 0x989c V 0x110000
RF 0x989c V 0x6100a8
RF 0x989c V 0x423022
RF 0x989c V 0x2014008f
RF 0x989c V 0xc40002
RF 0x989c V 0x3000f2
RF 0x989c V 0x440016
RF 0x989c V 0x410040
RF 0x989c V 0x1805e
RF 0x989c V 0xc0ab
RF 0x989c V 0xe1
RF 0x989c V 0x80
RF 0x989c V 0xd4
RF 0x98d0 V 0x10000f
--AP ar5416InitUserSettings ahp->ah_miscMode 0x8
ar5416Reset Setting CFG 0x10a
Country ie is <6>br0: port 2(ath0) entering learning state
../../common/InbWlan/InbWlan.cpp(241):UDP recv m_recvPort[0]= 2048
../../common/InbWlan/InbWlan.cpp(321):WLAN Received
Data; Length = 5
../../common/InbWlan/InbWlan.cpp(331):PORT received; continueing..
../../common/InbWlan/InbWlan.cpp(3
17):Inside the thread
../../common/UdpLib/UdpLib.cpp(210):Entered udp_read
Flushing old station entries
Deauthenticate a
ll stations
l2_packet_receive - recvfrom: Network is down
l2_packet_receive - recvfrom: Network is down
../../common/Mas
terControl/Info.cpp(85):Info::GetAPNumRadio: called
../../common/WscCmd/WscCmd.cpp(590):WscCmd: ******AP started
../../
common/WscCmd/WscCmd.cpp(616):WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MODE recd
../../common/WscCmd/WscCmd.cpp(629):
**
***** MODE: Access Point *******
../../common/WscCmd/WscCmd.cpp(1131):WscCmd:ActualUIThreadProc: Started.
../../common/
InbEap/InbEap.cpp(246):********TimeoutEnable = 0
../../common/StateMachine/RegistrarSM.cpp(105):REGSM: Passthrug=1
../
../common/InbWlan/InbWlan.cpp(452):In CInbWlan::SetBeaconIE Length = 40
../../common/InbWlan/InbWlan.cpp(395):In CInb
Wlan::SendDataDown buffer Length = 51
../../common/UdpLib/UdpLib.cpp(173):Entered udp_write
../../common/InbWlan/InbWla
n.cpp(421):data has been send to lower layer port 0
../../common/MasterControl/MasterControl.cpp(1553):MC::SetBeaconIE
: call to trans->SetBeaconIE() ok
../../common/InbWlan/InbWlan.cpp(507):In CInbWlan::SetProbeRespIE Length = 126
../..
/common/InbWlan/InbWlan.cpp(395):In CInbWlan::SendDataDown buffer Length = 137
../../common/UdpLib/UdpLib.cpp(173):Ent
ered udp_write
../../common/InbWlan/InbWlan.cpp(421):data has been send to lower layer port 0
../../common/MasterContro
l/MasterControl.cpp(1745):MC::SetProbeRespIE: call to trans->SetProbeRespIE() ok
../../common/MasterControl/MasterCont
rol.cpp(3044):ENRSM:setProcessStatus:0
../../common/StateMachine/StateMachine.cpp(442):SM: Restarting the State Machi
ne
../../common/StateMachine/StateMachine.cpp(375):SM: Deleting regData
../../common/StateMachine/StateMachine.cpp(442)
:SM: Restarting the State Machine
../../common/StateMachine/StateMachine.cpp(375):SM: Deleting regData
br0: topology ch
ange detected, propagating
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
router mips #238 Wed Nov 28 21:03:53 JST 2007
router login:
Planex vendor firmware Version 1.00.16 Build Date Wed Jul 9 16:45:32 JST 2008:
U-Boot 1.1.4 (Oct 25 2007 - 15:28:59)
AP81 (ar7100) U-boot
DRAM:
sri
32 MB
Top of RAM usable for U-Boot at: 82000000
Reserving 222k for U-Boot at: 81fc8000
Reserving 192k for malloc() at: 81f98000
Reserving 44 Bytes for Board Info at: 81f97fd4
Reserving 36 Bytes for Global Data at: 81f97fb0
Reserving 128k for boot params() at: 81f77fb0
Stack Pointer at: 81f77f98
Now running in RAM - U-Boot at: 81fc8000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
Fetching MAC Address from 0x81fedb10
eth0: 00:90:cc:f4:9c:a6
dup 1 speed 100
eth0 up
eth0
====check reset button function====
### main_loop entered: bootdelay=4
### main_loop: bootcmd="bootm 0xbf050000"
Hit any key to stop autoboot: 0
## Booting image at bf050000 ...
Image Name: Linux Kernel Image
Created: 2008-07-09 11:26:59 UTC
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 1358397 Bytes = 1.3 MB
Load Address: 80060000
Entry Point: 80301000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80301000) ...
## Giving linux memsize in bytes, 33554432
Starting kernel ...
Linux version 2.6.15--LSDK-7.1.3.58 (ttajima@localhost.localdomain) (gcc version 3.4.4) #226 Wed Jul 9 16:45:32 JST 8
flash_size passed from bootloader = 8
arg 1: console=ttyS0,115200
arg 2: root=31:03
arg 3: rootfstype=jffs2
arg 4: init=/sbin/init
arg 5: mtdparts=ar7100-nor0:256k(u-boot),64k(u-boot-env),1408k(uImage),6208k(rootfs),128k(config),128k(ART)
arg 6: mem=32M
CPU revision is: 00019374
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7100-nor0:256k(u-bo
Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 256 (order: 8, 4096 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29152k/32768k available (1979k kernel code, 3600k reserved, 708k data, 112k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
AR7100 GPIOC major 0
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
Serial: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
Creating 6 MTD partitions on "ar7100-nor0":
0x00000000-0x00040000 : "u-boot"
0x00040000-0x00050000 : "u-boot-env"
0x00050000-0x001b0000 : "uImage"
0x001b0000-0x007c0000 : "rootfs"
0x007c0000-0x007e0000 : "config"
0x007e0000-0x00800000 : "ART"
Port Status c000004
ar7100-ehci ar7100-ehci.0: ATH EHCI
ar7100-ehci ar7100-ehci.0: new USB bus registered, assigned bus number 1
ar7100-ehci ar7100-ehci.0: irq 3, io mem 0x1b000000
hcc_params addr 0xbb000108 val 0x6 hcs_params addr 0xbb000104 val 0x10011
ar7100-ehci ar7100-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Netfilter messages via NETLINK v0.30.
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
ip_conntrack version 2.4 (256 buckets, 2048 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ar7100wdt_init: Registering WDT success
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing unused kernel memory: 112k freed
mount: Mounting devpts on /dev/pts failed: No such file or directory
ag7100_mod: module license 'unspecified' taints kernel.
AG7100: Length per segment 1536
AG7100: Max segments per packet 1
AG7100: Max tx descriptor count 40
AG7100: Max rx descriptor count 252
AG7100: fifo cfg 3 00780008
AG7100CHH: Mac address for unit 0
AG7100CHH: 00:90:cc:f4:9c:a6
AG7100CHH: Mac address for unit 1
AG7100CHH: 00:90:cc:f4:9c:a7
ag7100_ring_alloc Allocated 480 at 0x803b3200
ag7100_ring_alloc Allocated 3024 at 0x80313000
AG7100: cfg1 0x3f cfg2 0x7014
AG7100: unit 0 phy is up...RMii 100Mbps full duplex
AG7100: pll reg 0x18050014: 0x13000a44 AG7100: cfg_1: 0x7ff0000
AG7100: cfg_2: 0xfff
AG7100: cfg_3: 0x780008
AG7100: cfg_4: 0xffff
AG7100: cfg_5: 0x7efef
AG7100: done cfg2 0x7115 ifctl 0x10000 miictrl 0x13
Writing 4
ag7100_ring_alloc Allocated 480 at 0x8122ee00
ag7100_ring_alloc Allocated 3024 at 0x8132d000
AG7100: cfg1 0x2f cfg2 0x7014
AG7100: unit 1: phy not up carrier 1
Writing 6
ag7100_ring_free Freeing at 0x803b3200
ag7100_ring_free Freeing at 0x80313000
ag7100_ring_alloc Allocated 480 at 0x803b3200
ag7100_ring_alloc Allocated 3024 at 0x80313000
AG7100: cfg1 0x3f cfg2 0x7014
AG7100: unit 0 phy is up...RMii 100Mbps full duplex
AG7100: pll reg 0x18050014: 0x13000a44 AG7100: cfg_1: 0x7ff0000
AG7100: cfg_2: 0xfff
AG7100: cfg_3: 0x780008
AG7100: cfg_4: 0xffff
AG7100: cfg_5: 0x7efef
AG7100: done cfg2 0x7115 ifctl 0x10000 miictrl 0x13
Writing 4
ag7100_ring_free Freeing at 0x8122ee00
ag7100_ring_free Freeing at 0x8132d000
ag7100_ring_alloc Allocated 480 at 0x8122ee00
ag7100_ring_alloc Allocated 3024 at 0x8132d000
AG7100: cfg1 0x2f cfg2 0x7014
Writing 6
# EOPNOTSUPP
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
killall: udhcpd: no process killed
loEOPNOTSUPP
no wirelEOPNOTSUPP
ess extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
br0 no wireless extensions.
Args: 1
ath_hal: 0.9.17.1 (AR5416, REGOPS_FUNC, WRITE_EEPROM, 11D)
wlan: 0.8.4.2 (Atheros/multi-bss)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: no version for "_ath_hal_attach" found: kernel tainted.
killall: udhcpc: no process killed
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 0.9.4.5 (Atheros/multi-bss)
Howl Revision ID 0xb5
No MBSSID aggregation support=====simple_config_callback registered=====
wifi0: Atheros AR9100 WiSoC: mem=0xb80c0000, irq=2
route: SIOC[ADD|DEL]RT: No such process
wlan: mac acl policy registered
Creating ap for planexuser on
Added ath0 mode master
Interface doesn't accept private ioctl...
HALDbg (8BE0): Operation not permitted
ieee80211_ioctl_setmode: CHH Mode: 11NGHT40PLUS
ath_set_config: Setting ATH parameter
ath_set_config: Setting ATH parameter
ath_set_config: Setting ATH parameter
ath_set_config: Setting ATH parameter
ath_set_config: Setting ATH parameter
ieee80211_ioctl_setparam: CHH Calling ieee80211_open
Created ath0 mode ap for planexuser
../../common/MasterControl/Info.cpp(66):Info::SetWscConfigPath: called
../../common/MasterControl/Info.cpp(79):Info::SetAPNumRadio: called
../../common/UdpLib/UdpLib.cpp(78):Entered udp_open
../../common/UdpLib/UdpLib.cpp(96):Socket open successful, sd: 4
../../common/UdpLib/UdpLib.cpp(114):Entered udp_bind
../../common/UdpLib/UdpLib.cpp(129):Binding successful for socket [4]
../../common/WscCmd/WscCmd.cpp(425):WscCmd:ActualCBThreadProc: Started
loEOPNOTSUPP
no wirelEOPNOTSUPP
ess extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
br0 no wireless extensions.
wifi0 no wireless extensions.
Force rf_pwd_icsyndiv to 1 on 2412 (1 0)
--AP ar5416InitUserSettings ahp->ah_miscMode 0xc
ar5416Reset Setting CFG 0x10a
Howl Revision ID 0xb5
Country ie is <6>Force rf_pwd_icsyndiv to 2 on 2422 (1 0)
--AP ar5416InitUserSettings ahp->ah_miscMode 0xc
ar5416Reset Setting CFG 0x10a
Howl Revision ID 0xb5
device ath0 entered promiscuous mode
br0: port 2(ath0) entering learning state
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
ARPING to 192.168.1.1 from 192.168.1.1 via br0
Sent 1 probes (1 broadcast(s))
Received 0 reply
../../common/WscCmd/WscCmd.cpp(1131):WscCmd:ActualUIThreadProc: Started.
../../common/MasterControl/MasterControl.cpp(88):MasterControl constructor
../../common/WscCmd/WscCmd.cpp(243):WscCmd::MC instantiated ok
../../common/Transport/Transport.cpp(79):CTransport Construction
../../common/MasterControl/MasterControl.cpp(209):MC::Init: Init complete ok
../../common/WscCmd/WscCmd.cpp(245):WscCmd::MC intialized ok
../../common/WscCmd/WscCmd.cpp(119):WscCmd::Init ok, starting stack...
../../common/MasterControl/Info.cpp(156):Read WSC Config File:/var/wsc_config.txt
../../common/MasterControl/Info.cpp(171):Info::ReadConfigFile:File open ok
../../common/MasterControl/Info.cpp(1273):Use eth0 address 0:90:cc:f4:9c:a6
../../common/Transport/Transport.cpp(154):In CTransport::ActualCBThreadProc
../../common/Transport/Transport.cpp(158):Calling Dequeue
../../common/MasterControl/MasterControl.cpp(1222):MC::SwitchModeOn: EModeApProxyRegistrar enter
../../common/StateMachine/StateMachine.cpp(71):RegistrarSM constructor
../../common/MasterControl/MasterControl.cpp(2961):***** WPA_PSK =
../../common/StateMachine/RegistrarSM.cpp(73):InitializeSM, locEna=1, Passthr=1
../../common/InbEap/InbEap.cpp(95):CInbEap Construction
../../common/InbEap/InbEap.cpp(114):Sizeof(WSC_NOTIFY_DATA) = 19
../../common/UdpLib/UdpLib.cpp(78):Entered udp_open
../../common/UdpLib/UdpLib.cpp(96):Socket open successful, sd: 8
../../common/UdpLib/UdpLib.cpp(114):Entered udp_bind
../../common/UdpLib/UdpLib.cpp(129):Binding successful for socket [8]
../../common/InbEap/InbEap.cpp(360):In CInbEap::StaticRecvThread
../../common/InbEap/InbEap.cpp(372):CInbEap::ActualRecvThread Started
../../common/InbWlan/InbWlan.cpp(73):CInbWlan Construction
../../common/UdpLib/UdpLib.cpp(78):Entered udp_open
../../common/UdpLib/UdpLib.cpp(96):Socket open successful, sd: 9
../../common/UdpLib/UdpLib.cpp(114):Entered udp_bind
../../common/UdpLib/UdpLib.cpp(129):Binding successful for socket [9]
../../common/InbWlan/InbWlan.cpp(288):In CInbWlan::StaticRecvThread
../../common/InbWlan/InbWlan.cpp(313):CInbWlan::ActualRecvThread Started
../../common/InbWlan/InbWlan.cpp(317):Inside the thread
../../common/UdpLib/UdpLib.cpp(210):Entered udp_read
../../common/StateMachine/StateMachine.cpp(71):RegistrarSM constructor
../../common/MasterControl/MasterControl.cpp(2757):Generated devPwd: 12345670
../../common/WscCmd/WscCmd.cpp(470):WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MSG recd
../../common/WscCmd/WscCmd.cpp(1453):WscCmd::CallbackProc Enqueue done
../../common/MasterControl/MasterControl.cpp(1370):*** Init Enrolle Stat machine
../../common/MasterControl/MasterControl.cpp(1379):MC::SwitchModeOn: Starting AP
../../common/WscCmd/WscCmd.cpp(522):WscCmd:ActualCBThreadProc: CB_MAIN_START_AP recd
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
../../common/WscCmd/WscCmd.cpp(1466):WscCmd::AP tmp file =cp /var/hostapd.open
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
../../common/WscCmd/WscCmd.cpp(1453):WscCmd::CallbackProc Enqueue done
../../common/MasterControl/MasterControl.cpp(1419):MC::SwitchModeOn: Exit
../../common/MasterControl/MasterControl.cpp(352):MC::StartStack: Informing app of mode
../../common/WscCmd/WscCmd.cpp(1453):WscCmd::CallbackProc Enqueue done
../../common/MasterControl/MasterControl.cpp(371):MC::SwitchModeOn: Done callback
../../common/WscCmd/WscCmd.cpp(123):WscCmd:: Stack started ok
../../common/WscCmd/WscCmd.cpp(1472):WscCmd::AP Config file copied: cmd=cp /var/hostapd.open /var/hostapd.conf
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
../../common/WscCmd/WscCmd.cpp(1641):WscCmd::Params added to AP config file
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
../../common/WscCmd/WscCmd.cpp(1641):WscCmd::Params added to AP config file
../../common/MasterControl/Info.cpp(374):mb_nwKeySet = 1
../../common/MasterControl/Info.cpp(382):m_nwKey =
../../common/MasterControl/Info.cpp(73):Info::GetWscConfigPath: called
ath_netdev_stop: The stopping of the running
br0: port 2(ath0) entering disabled state
ieee80211_ioctl_setparam: CHH Calling ieee80211_open
Force rf_pwd_icsyndiv to 2 on 2422 (1 0)
--AP ar5416InitUserSettings ahp->ah_miscMode 0xc
ar5416Reset Setting CFG 0x10a
Howl Revision ID 0xb5
Country ie is <6>br0: port 2(ath0) entering learning state
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
../../common/InbWlan/InbWlan.cpp(241):UDP recv m_recvPort[0]= 2048
../../common/InbWlan/InbWlan.cpp(321):WLAN Received Data; Length = 5
../../common/InbWlan/InbWlan.cpp(331):PORT received; continueing..
../../common/InbWlan/InbWlan.cpp(317):Inside the thread
../../common/UdpLib/UdpLib.cpp(210):Entered udp_read
l2_packet_receive - recvfrom: Network is down
l2_packet_receive - recvfrom: Network is down
../../common/MasterControl/Info.cpp(85):Info::GetAPNumRadio: called
../../common/WscCmd/WscCmd.cpp(610):WscCmd: ******AP started
../../common/WscCmd/WscCmd.cpp(636):WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MODE recd
../../common/WscCmd/WscCmd.cpp(649):
******* MODE: Access Point *******
../../common/WscCmd/WscCmd.cpp(1151):WscCmd:ActualUIThreadProc: Started.
../../common/InbEap/InbEap.cpp(246):********TimeoutEnable = 0
../../common/StateMachine/RegistrarSM.cpp(105):REGSM: Passthrug=1
../../common/InbWlan/InbWlan.cpp(452):In CInbWlan::SetBeaconIE Length = 40
../../common/InbWlan/InbWlan.cpp(395):In CInbWlan::SendDataDown buffer Length = 51
../../common/UdpLib/UdpLib.cpp(173):Entered udp_write
../../common/InbWlan/InbWlan.cpp(421):data has been send to lower layer port 0
../../common/MasterControl/MasterControl.cpp(1553):MC::SetBeaconIE: call to trans->SetBeaconIE() ok
../../common/InbWlan/InbWlan.cpp(507):In CInbWlan::SetProbeRespIE Length = 126
../../common/InbWlan/InbWlan.cpp(395):In CInbWlan::SendDataDown buffer Length = 137
../../common/UdpLib/UdpLib.cpp(173):Entered udp_write
../../common/InbWlan/InbWlan.cpp(421):data has been send to lower layer port 0
../../common/MasterControl/MasterControl.cpp(1745):MC::SetProbeRespIE: call to trans->SetProbeRespIE() ok
../../common/MasterControl/MasterControl.cpp(3044):ENRSM:setProcessStatus:0
../../common/StateMachine/StateMachine.cpp(442):SM: Restarting the State Machine
../../common/StateMachine/StateMachine.cpp(375):SM: Deleting regData
../../common/StateMachine/StateMachine.cpp(442):SM: Restarting the State Machine
../../common/StateMachine/StateMachine.cpp(375):SM: Deleting regData
# uname -a
Linux router 2.6.15--LSDK-7.1.3.58 #226 Wed Jul 9 16:45:32 JST 2008 mips unknown
#
# cat /proc/mtd
dev: size erasesize name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00160000 00010000 "uImage"
mtd3: 00610000 00010000 "rootfs"
mtd4: 00020000 00010000 "config"
mtd5: 00020000 00010000 "ART"
#
plug in USB memory stick:
# usb 1-1: new high speed USB device using ar7100-ehci and address 4
ehci-9130: hub_port_reset
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: Model: USB Flash Memory Rev: PMAP
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 15667200 512-byte hdwr sectors (8022 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 15667200 512-byte hdwr sectors (8022 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
sda: sda1
sd 1:0:0:0: Attached scsi removable disk sda
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
(Last edited by RoundSparrow on 27 Mar 2009, 16:23)